Something usually tips it. A breaker that resets fine on Monday and trips again by Thursday. An outlet in the kitchen that stopped working and took the one next to it with it. A panel that hums faintly in a way it did not used to. In a town like New Haven, where a lot of the housing stock was built decades before modern electrical loads were imagined, those moments come up more than people expect. When they do, the question is the same: who do you call, and what happens next.
We handle electrical work across New Haven and the surrounding Macomb County area, from straightforward repairs to panel replacements and full rewiring.
Call (248) 791-9979 and you will get a price before anything is scheduled. We are open every day from 9:00 AM to 8:00 PM.
An inspection is the right starting point when you do not know what you have. Older homes in this area sometimes carry wiring that has never been formally reviewed: knob-and-tube in the attic, aluminum branch circuits at the outlets, or a panel that was upgraded partway and left with a mix of old and new. An inspection documents what is there, what the condition is, and what needs attention. Landlords use them before a tenancy starts. Buyers use them before a closing. Homeowners use them when something feels off and they want a clear picture before deciding what to do.
A Level 2 charger needs a dedicated 240-volt circuit run from the panel to the garage or parking area. Most homes in New Haven were not wired with one. We check the panel's available capacity first, confirm it can carry the new circuit, and run the wiring from there. If the panel is already at its limit, that conversation happens before the work starts, not after.
An outdoor outlet that is not properly enclosed or rated for exposure can fail in the first hard rain and become a hazard well before it fails visibly. We install weatherproof GFCI outlets and enclosures for exterior walls, garages, sheds, and outbuildings. The circuit protection is sized and placed to code, which matters for any outdoor installation where moisture is a factor.
When wiring has reached the end of its useful life, a repair does not solve the underlying problem. Whole-home rewiring replaces the existing system with modern wiring, proper grounding throughout, and circuit protection sized to handle current electrical demands. Partial rewiring addresses specific areas: a kitchen that is being renovated, a basement being finished, or a wing of the house where the wiring is clearly deteriorated. The scope gets confirmed on the call before we schedule anything.
Older wiring sometimes does not support modern smart switches or dimmers without modification. A neutral wire is required for most smart switch configurations, and many older boxes do not have one. We check what is in the wall before committing to a scope, so the quote reflects the actual job rather than the ideal version of it.
A generator that is plugged into a dryer outlet with an improvised cord is a hazard to the household and to anyone on the utility line during an outage. A proper hookup means a transfer switch or interlock kit installed at the panel, wiring run to the generator connection point, and a load assessment to confirm the circuits being covered are the right ones. We stay on the wiring side of the job. The generator itself runs on its own fuel system, and that part belongs to whoever supplies it.
Panel and wiring work finished to code is the standard for every job, whether it is a single circuit or a full panel replacement.
Electrical pricing is not a flat rate because the job is not a flat rate. What a repair actually involves depends on what the fault turns out to be, how far into the wall or ceiling it sits, and whether the existing circuit or panel can carry the change being made. A tripped breaker that resets and holds is a different job from one that trips because the circuit is overloaded or because there is a fault somewhere along the run.
The things that move a quote are straightforward. If reaching the problem means opening a wall or pulling wire through a finished ceiling, that changes the labor. If the panel is at capacity and a new circuit requires a panel upgrade first, that changes the scope. If the existing wiring is aluminum or deteriorated and a repair requires bringing the connection up to current standards, that changes the materials. None of those are surprises if they are explained on the call before anything is scheduled.
When you call, describe what you are seeing and where it is. We ask the questions needed to scope the work accurately, and you get a price before we come out. No-pressure estimates, priced up front, so you know what the work involves before we arrive.
Electrical work does not always happen at a convenient height or in an easy-to-reach location. Attic wiring, crawl space circuits, and high-ceiling fixture installations each add a layer of planning that a straightforward outlet swap does not require.
Wiring that runs through an attic or crawl space is often the wiring that has been there the longest and seen the least attention. Heat cycles in an uninsulated attic degrade insulation over time. Moisture in a crawl space does the same. When a repair or rewiring job involves those spaces, the scope includes assessing what is already there, not just running the new circuit.
A ceiling fan or light fixture at twelve or fourteen feet is a different job from one at eight. The fixture still needs a properly rated box, the right wiring, and a switch leg that matches the configuration. The height changes how the job is staged, not what it requires. We account for that in the scope before the visit.
We'll sort the wiring and clean up after, whatever the access situation turns out to be.
We are open every day from 9:00 AM to 8:00 PM. When you call, we confirm what the schedule allows and find a time that works. If the problem is one that will not keep, say so on the call and we will tell you what the nearest available slot looks like.
For rental properties and businesses that need to stay operational, we work around the situation. That means being clear about what access is needed, how long the visit is likely to run, and whether any circuits will be out of service during the work. You're talking to someone who knows the area and the homes in it, so the conversation about what the job involves happens before anyone shows up at the door.
We answer when you call. We explain the work. We leave it safe. Most of what comes up before a visit is answered on the full electrical services list.
Booking electrical work on a rental involves a few moving parts that an owner-occupied home does not. The person calling is not always the person who will be present. The invoice may need to go to a property manager rather than the occupant. Access has to be arranged with the tenant, and the tenant may need advance notice before anyone enters.
We handle the scheduling conversation with whoever is coordinating the work. If the landlord wants a written record of what was found and what was done, the scope and the outcome are explained clearly before and after the visit. For landlords managing more than one unit in the New Haven area, we handle repairs, inspections, and panel work across multiple properties. Electrical service scheduled without the runaround applies to rental calls the same as any other.
The panel in an apartment or condo is not always where you expect it. In older multi-unit buildings it may be in a hallway, a utility room, or a shared basement space. In some buildings the panel inside the unit controls only part of the circuits, and shared systems like hallway lighting or common-area outlets are on a separate service that the building manages.
Before we scope work in a multi-unit property, we confirm which circuits are inside the unit and which are shared. Work on shared systems usually requires coordination with the building owner or manager, and that is worth sorting out before the visit rather than on the day. If the panel inside the unit is full or undersized for what the tenant or owner needs, we explain the options and what the upgrade would involve.
We serve New Haven and the surrounding communities throughout Macomb County. That includes Chesterfield Township, New Baltimore, Richmond, Ray Township, and Casco Township. Residential and rental properties across that area are all within our regular coverage. Call to confirm availability for your address if you are on the outer edge of the area.
Regional ice storms and wind events can send voltage spikes through the utility line, and a single surge event can damage appliances, electronics, and EV charging hardware across the whole house. A whole-home surge protector installed at the panel intercepts those spikes before they reach the branch circuits. It is a practical addition any time the panel is already open for an upgrade or a new circuit installation.
The work area is cleaned up before we leave. Devices are installed and covers are on. The panel is labeled if labeling was part of the job. Any debris from the work is removed. We test the circuits before leaving so the system is confirmed working when we go.
A clear written account of what was inspected, what was found, and what was addressed gives a landlord documentation of the property's electrical condition at a specific point in time. That record is useful when a tenant reports a problem, when a property needs to meet current code for a rental certificate, or when the property changes hands. Ask about what the inspection covers when you call to schedule.
We assess the transfer switch, the panel connection, and the wiring condition as part of the visit. An unsafe generator hookup, such as a backfeed connection without a proper transfer switch, is a hazard that we document and explain clearly. We give you a price for bringing it up to a safe configuration before any correction work starts.
Call (248) 791-9979 to get a quote on any electrical job in New Haven or the surrounding area.
We are open every day from 9:00 AM to 8:00 PM. Describe what you are seeing, and we will tell you what the work involves and what it costs. The price is agreed before the visit is booked, and nothing starts until you say so. We handle the full range of residential and rental electrical work across Macomb County, and the call is where it all begins.
Fast diagnosis. Pricing set out up front. Clean work.
Electrical service reaches these neighboring areas too: Chesterfield Township, Ray Township, Armada, Harrison Township, Mount Clemens. Everywhere else we go is in our area list.
Below is a plain-language look at the electrical work we handle across New Haven, Macomb County and Macomb County. Each row covers what the service involves, who it fits best, and one practical thing worth knowing before you call. Pricing is discussed on the call, before anything is scheduled, so you can make an informed decision without any commitment.
| Service Type | What It Covers | Ideal For | Things to Know |
|---|---|---|---|
| Electrical Panel & Service Upgrades | 200-amp service upgradeNew breaker box installationLoad calculation and service entrance workSubpanel installation for garages and additions | Older Macomb County homes adding EV chargers, heating circuits, or major appliances to an undersized 100-amp panel | Panel work is finished to code and covers the full service entrance where the incoming capacity needs to match the new box. A load calculation is part of every upgrade. |
| Electrical Repairs & Troubleshooting | Dead outlets and tripped GFCI devicesFault tracing at the panel and circuit levelBurning smell and heat diagnosisFlickering light and power loss investigation | Any homeowner or property manager dealing with an active electrical problem | We read the panel and trace the fault to its source before quoting any repair work, so you are not paying to replace parts that are not the cause. |
| Ceiling Fan Installation | Fan-rated box installationSeparate switch leg wiringRemote and smart control setupReplacement fan assessment | Homeowners replacing a light fixture with a ceiling fan or upgrading an existing fan to independent fan and light control | The ceiling box has to be rated for a fan's weight and movement. We check the existing box and wiring before committing to a scope. |
Call (248) 791-9979 to describe the job and get a price before anything is scheduled. We are open every day from 9:00 AM to 8:00 PM.
(248) 791-9979